Seagate dockstar as a nas12/18/2022 I also notice the Seagate uses SalesForce for its customer service. Seagate appears to use much the same approach to customer service as SAP, which is to say bureaucratic and counterintuitive. This is irritating enough without having to deal with Seagate's labyrinthine Web site to make the request. This is a good idea but, I presume, due to export restrictions, you have to apply to Seagate Technical Support and supply the serial number of your drive and your address to get this version. They offer power management (you can set how long to wait before entering power-saving mode) and, using the Seagate Manager application, you can schedule automatic backups and use the drive to synchronize two computers.Ī recently released update of the Seagate Manager adds a new feature: Encrypted folders. This is the dockstar in all it’s nude glory.The FreeAgent Go part of the system is a slim (5.12"h by 3.15"w by 0.83"d and weigh just 0.35lb), elegantly styled USB 2.0 drive available in capacities ranging from 250GB ($89.99) to 1TB ($229.99). The front of the device is to the right in this photograph. The small black square is Nanya 1Gb (comes out to ~128 megabytes) DDR-2 RAM in a BGA package. Datasheet available here and the large square is the device’s main processor. From research I have performed, this appears to be a Marvell 1.2GHZ processor (just like the sheevaplug devices that Marvell is also selling. I tried to pull some more datasheets from, but their datasheet listing is quite lacking. For now, just know that it’s an arm compliant processor and when I post an update article, I will have more juicy details on the capabilities of the processor. Also of note, just below and to the right of the processor is a small ten pin header. Presumably this can be used for a serial port however I do not have the cable for that. Once I get it in and test it, I will update this article with a pinout diagram for you. Since this device is so low-level I would not recommend trying to connect a regular serial port to it directly as it more than likely requires a level shifter like a MAX232 to bring the -12/+12VDC down into something that won’t blast the components. This is the bottom of the dockstar’s mainboard. Unfortunately, the board is now oriented that the front of the dockstar is now at the bottom of the picture. (Bad cameraman, no cookie.) There’s not really much to note here as the board layout is jam packed with passive components. The large black square on the lower right is the NAND storage for the device and while I couldn’t pull up the datasheet for it, the guys over at PlugPBX already had a forum post that showed the Dockstar’s hardware specs for us. According to their chart, the dockstar’s storage is 256MB. which should be more than adequate for general Linux fun. The small chip just under the black tape in the upper right hand corner of the board is presumably the ethernet NIC however googling the chip numbers came up with nothing. Just looking at the hardware overall, it would appear that the Seagate Dockstar is a very capable device that just needs to be altered to run whatever we choose to run with it. While the software on the device (stock) comes with a filesharing service called Pogoplug, I do not intend on using that software and will be looking to get this device as far away from stock as possible. Here is a list of some things I’ve been thinking of doing with it so far: Seagate freeagent dockstar price software# Home NAS (without Internet file sharing).multihomed router (I have a stack of pegasus USB modules).semiportable network notification device (USB to parallel port, HD44780 LCD display). realtime data acquisition device (USB logger and serial ports?). Seagate freeagent dockstar price software#Īpple MT-DAAPd server for streaming music to iTunes installations on your local network.Seagate freeagent dockstar price update#.Seagate freeagent dockstar price serial#.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |